Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they are not susceptible to rust or rot.

It is crucial to wash and oil UPVC windows and Window doctor doors on a regular basis. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and even be fatal. It is important to take the time to make sure that you're doing everything you can to keep your windows in good condition.

For single pane windows it is fairly easy to replace them, and the new window will usually fit inside the frame that was previously installed easily. However when you have double pane windows that are anchored by internal beading, it will be more difficult to take out the panes that are in place and replace them with new ones. In this case you'll need to locate some plastic spacers that will help the new pane to fit perfectly into the window frame.

If you are going to try to remove the window panes by yourself it is crucial to wear the appropriate safety equipment that includes gloves with a thick layer of material and protective eyewear. It is also an excellent idea to lay down a drop cloth prior to when you begin working on the glass so that any fragments of glass fall onto the fabric instead of onto the floor, where they could be trodden under and cause further damage.

After the glass has been removed, it's a good idea to cover the gap with packaging tape or duct tape to block water and drafts from entering the home until a professional comes out and repair the window. This will also act as a barrier, deterring any intruders from getting access into your home. If the gap between the door and the window is large, Window doctor you might prefer an alarm system that includes windows. This will provide the best of both.

2. Sagging

Upvc windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber windows made of sash. However, over time, they may be afflicted by a variety of problems including sagging. A sagging window in uPVC can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to lose its shape, it's important to act quickly to stop the issue from getting worse.

To fix a window that is sagging you can try repositioning the hinges. To accomplish this, you'll need to open the window so that you can access the frame. Then, remove both the hinges on the top and bottom with a screwdriver and adjust the hinges clockwise or counter-clockwise. After you've repositioned the hinges, close the window and check for fitting. If you're happy with the fit, tighten the screws until they remain in place.

If you aren't able to move the hinges, you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, causing them to lose their tightness. It is essential to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

UPVC handles can also loosen up. Most often this is due to screws that have come loose over time. However, it can be due to the fact that the handle mechanism has been worn out. Fortunately, it's easy to repair a loose uPVC window handle yourself. First, you'll need to close your window and do a test to ensure that it fits. The joints at the corners of the sash should align with the joint on the casing. If it does not then you can use the screwdriver to loosen up the handle. Then turn the mechanism into position.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains, it is important that you take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature inside your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame has been damaged or missing.

This is an easy fix that can be accomplished by any DIYer who has the ability. Depending on the severity of the issue the old caulking may require removal before a new layer is applied. It is crucial to keep in mind that when it is about uPVC window repairs you should avoid the temptation to "over-caulk in order to make the area harder to clean and could reduce your energy efficiency.

Make sure that the drainage holes have no debris in them and that the sill pan has been properly angled to drain away from the window. In more serious situations, you may have to replace the window doctor near me.

Moldy sills and rotten ones are also signs of water leakage. This fungus thrives under damp conditions and can spread quickly throughout the home.

It is also important to remember that if the leak is coming from between the glass of your double-glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sagging. A uPVC specialist can easily solve this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

Hinges may be to blame when your uPVC window is difficult to open, or if it opens in a breeze. They can be replaced by any competent DIYer and are usually completed in just a few minutes.

Like any mechanical component hinges are prone to be damaged over time. The process of replacing a hinge on a window is an easy procedure, but it is simpler with someone else to assist in holding the frame in place.

It is also worth checking that the uPVC hinges are opened and closed in the correct direction. Look for the arrows on each hinge to determine the direction in which the window should be opened.

The issue could be caused either by opening the window incorrectly or by a poor installation in the factory. This can often be resolved by sending us a photograph on our website. We will be happy to give you advice.

It is also essential to ensure that the hinges are lubricated on a regular basis. This can be done by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also helps prevent corrosion and reduce the risk of sticking. This should be done at least every year. WD40 and other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges may also become misaligned due to wear, causing a gap between the frame and sash. If they are beyond repair, it could be necessary to have them realigned. Second, the interlock can be disaligned. It is located on the hinge's side and may need to be cleaned. In some cases, it may be necessary to replace these.

The next common reason for draughts are the Window Doctor seals. They are susceptible to being worn out or damaged over time and let air escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass, which will help regulate indoor temperatures and will lessen the risk of draughts.

One of the most effective ways to cut down on draughts is by using a draught excluder. These are typically fabric tubes filled with some type of filler. They can be positioned on the top of your windowsill. These will help to stop cold air from entering and keep your home warm and cosy!

With a little regular maintenance and repairs your windows made of upvc will provide a great level of security and insulation for your home. It is crucial to realize that all windows have a life span and they may reach an point at which it is more cost-effective to replace them rather than fix them. If you are having issues with your upvc windows, it is always recommended to seek assistance from a professional as soon as possible.