How to Replace a Kia Sportage Replacement Key

For a number of Kia models keys, the key has an integrated keyless entry system. The key functions like remote controls, and is exchangeable by an Kia dealer.

Key fobs may stop working due to a variety of reasons, including the battery of the coin is dead, worn buttons signals, water damage, signal interference and a damaged receiver module. Here are some suggestions to assist you in getting your kia picanto key fob (homesite) sportage replacement key working again.

How to replace the remote key or smartkey?

The battery inside your Kia's smart key will eventually have to be replaced, regardless of whether it's a remote key, a push-to-start key or a regular key that doesn't have an electronic transponder. This is especially when your car displays a message telling you that the remote or smart keys are not powered by batteries.

Fortunately, it's quite simple to do. To replace the battery on the keyfob remove your mechanical key from the slit at the back of the fob. Then, push the cover open. A small screw will be in the key fob, which holds the battery in place. Remove the old battery by unscrewing the screw with the help of a small screwdriver. Install the new battery and then close the opening on the key fob.

When the key fob is equipped with an updated battery check it by pressing the locks and unlock buttons. If the doors unlock and lock according to your expectations, then you're in good shape! You can now utilize Kia's hands-free lock/unlock function when your fingers are cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a computer that is only available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal), do not need programming. If your key requires to be programmed again, you must be aware of the key code printed on the tag that identifies the key and then record the number in a secure place.

How do I replace the battery?

If the Kia key fob doesn't respond when you press the lock/unlock button, it's likely that the battery is not fully charged. A battery that is not functioning properly could cause other problems like the check engine light turning on or delayed engine cranking. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires just a few tools.

Before you begin the process be sure that your vehicle is turned off and all doors are shut. Find the small metal or plastic piece at the bottom of the key fob. Then, jiggle it until the metal key falls out. You can then insert this key into the handle on the door of your driver to open your car.

To replace the key fob's battery, remove the cover at the rear and use a plier bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and then orient the replacement battery so that its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid bending or damaging the contacts on the metal.

Once the new battery is installed and the key fob is turned on, turn it off and on in the ignition repeatedly until the door locks cycle. You can then test your Kia's key fob once more to ensure it is working correctly.

How do you replace a smart key

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference between the two is that the smart key has the small blade of a key tucked inside it, while the standard fob isn't equipped with. Both kinds of key fobs come with a battery inside them that eventually will need to be replaced. It is a simple process that takes only two minutes.

Before you start it is important to ensure that you are on a flat surface with sufficient lighting and that the Kia is off. Be aware that there are tiny parts inside the fob that can be removed if not vigilant.

The first step is to locate the small release button that is located on the lower backside of your fob. It will be a circular button or a rectangular slot. Once you press this the mechanical key blade will pop out and you will be able to open the key fob.

After the key fob has been opened, take out the old battery. The new battery is a one called CR-2032 and can be purchased through the internet or at a local auto parts shop. After installation, you should be able to lock, unlock and start your car with your key fob, even if your engine isn't running!

How do I replace a mechanical key

The Kia key fob is an amazing convenience that allows us to lock and unlock our car with the touch of a button. Like any other device it is possible that the Kia key fob might have issues. There are solutions to solve these issues and keep your key fobs in good working order for an extended period of time.

One of the most frequent problems is a low or dead battery. This could cause the fob to cease working or stop working at times. If this is the case then try replacing the battery with a fresh new one.

If this doesn't solve the problem, use a standard flathead screwdriver to push the fob's plastic casing open. Be careful not to scratch any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to make sure it is working properly. If the fob isn't functioning, contact an authorized locksmith or dealer to help solve the issue. Make sure they cut you an emergency key that works for all trunk and door cylinders in order to prevent lockouts in the future.